Une question ?
Appelez-nous au
01 30 41 23 62
fabricant de capteurs
et systèmes de mesure

THERMOCOUPLE---RTD PT100---PRESSION---FORCE---ACQUISITION---ACCESSOIRES---PYROMETRE---FOUR---JAUGE---DEPLACEMENT---AMS 2750---AUTOCLAVE

Vibration transmitter
2170c
FP2170c
Speed range : 10, 20, 50, 100 mm/sec
Accuracy : +/-2%
Response time : 10 sec. environ
This transmitter is designed to monitor vibration intensities, for integrated electronic accelerometers. It directly converts accelerometer values (g) to speed (mm/s)
Ultra miniature pressure sensor
P-M5-Serie 0/350 Bar miniature
FP 507 Rev A 900€ UHT
Ultra miniature pressure sensor with M5 thread, with or without integrated electronics.
traction/compres. force sensor
FTCN 100 à 20 000 N
FP3400 D
500,00 €HT
Force sensor type from 100 to 20 000 N. Output on 2 m cable. Low level signal 1.5 mV / V. This good capacity sensor is intended for use in traction and compression. It is intended for fatigue tests. Its advantages are to ensure a low deformation and an insenability to the transverse forces. IP66 protection and its stainless steel body ensure its robustness.
Miniature force sensor
FC 10 à 5000N9
FP3502
500,00 €HT
Miniature force sensor in compression. Washer type, for use in compression. Sensor of small thickness. Intended for static or dynamic measurements. This sensor is available in 2 forms, with or without central hole, diameter 8 mm.
traction/compres. force sensor
FTCS 10 à 200 N
FP3300 600€ UHT
Miniature force sensor in tension and compression. Force sensor, small dimensions for large measuring ranges. Equipped with metric threads for use in traction as in compression, these sensors must not be subjected to off-axis loads.
Jacketed thermocouple miniature connector CC Series
CC type K J T S N E etc
FP 2122 CC
15,00 €HT
Thermocouples with semi-rigid metal sheath for all applications even difficult. Insulated hot weld, grounded or exposed. The user can deform, curve the sheath to adapt to its application without altering the performance of the sensor. Output on miniature size male connector (2 flat pins).
Jacketed thermocouple standard
CCS type K J T N S E
FP 2809
17,00 €HT
Thermocouples with semi-rigid metal sheath for all applications even difficult. Insulated hot weld, grounded or exposed. The user can deform, curve the sheath to adapt to its application without altering the performance of the sensor. Output on standard size male connector (2 round pins).
Pressure Sensor M10x1
PM10C-Serie 1/350 Bar miniature
FP P 602
Etendue de mesure : 1/350 Bar
Raccord mécanique :  M10x100
Signal de sortie :       0/5V,bas niveau,4/20mA
Application : Aéronautique, industrie

Transmetteur de pression miniature avec filetage en M10X1, avec ou sans électronique intégrée. Fabrication entièrement en inox. Autres versions en M4,M5,M6 nous consulter
Accéléromètre Industriel
V FP2367 Accélérométre
AC3030---G
Accéléromètre destiné au domaine industriel et permet de mesurer des faibles étendues de mesure.Le Boitier est en Aluminium, facile d'implantation pour de nombreuses applications.
Il est possible d'associer un amplificateur permettant une utilisation pratique.

High stability black body furnace general
CAL1200
CAL
Measurement temperature: 300 ° C / 1200 ° C
Power: 230VAC, 2.5KW
Application: Industry
Portable black body furnace with high stability. Digital self tuned PID controller.Weight approx. 50KG, dimensions 590x450x530mm.
Portable black body general
CAL110
CAL
Measuring temperature: 10 ° C / 110 ° C
Power: 230VAC, 0.5KW
Application: Industry
Portable black body general. Digital self tuned PID controller. Weight 12KG approx., dimensions 330x355x225mm.
Highly accurate pyrometer
E-series
E250 PL-E450 PL
Measurement temperature: 250 ° C / 1900 ° C
Spectral range : 1.0μm ... 1.6μm
Emissivity: 0.1 ... 1 adjustable
Accuracy: ± 0.3% of the measured value +1°C
Highly economical digital IR pyrometers with extended sensor head and separate electronic box. Inbuilt LCD display and keypad for parameterisation. Stainless steel sensor head and zinc electronic box.
Miniature sensor hygrometry
F2586-B
2586
Measuring range : 0 to 100%
Supply voltage : 5 Vcc
Accuracy : +/-3.5%
Output signal : 0.8 à 3.9 Vcc
Small sensor hygrometric measurement. It will allow you to perform measurements in confined spaces thanks to its custom design.
Peltier based temperature calibrator
CAL-15/110
CAL
Measurement temperature: -15 ° C/110 ° C
Power: 230VAC, 500W
Application : Industry
Peltier based temperature calibrator. Digital self tuned PID controller. Weight 11.70Kg, dimensions 380 x 170 x 188 mm.
Temperature calibrator
CAL120SP
CAL
Temperature range : 0°C/120°C
Power : 230VAC, 500KW
Application : Industry.
Peltier based temperature calibrator. Self-tuned PID controller with automatic super fine adjustement. Weight 14 KG, dimensions 380 x 170 x 188mm.
Liquid calibration bath
CAL250
CAL
Measurement temperature : 50°C/250°C
Power : 230VAC, 1.0KW
Application : Industry
High accuracy liquid calibration bath. Digital self-tuned PID controller. The unique features is portability with very high stability and uniformity. Weight 12 KG, dimensions 360x185x285mm.
Portable calibrator
CAL650
CAL
Measurement temperature : 50°C/650°C
Power : 230VAC, 1.0KW
Application : Industry
Portable calibrator. Self tuned PID controller with automatic super fine adjustment. Weight 8.80 Kg, 325 x 185 x 265 mm.
Highly accurate pyrometer
A-series
A250 PL/TL
Measurement temperature : 210/3000°C
Spectral range : 1.0...1.6μm
Emissivity : 0.1...1 adjustable
Accuracy :± 0.3% of the measured value + 1°C
Highly accurate on-line infrared non-contact pyrometer with Bluetooth for the communication between the pyrometer and the "Infrasoft" software. Stainless steel housing.
Highly accurate digital pyrometer
E-series
EL50
Measurement temperature : 0/800°C
Spectral range : 8...14μm
Emissivity : 0.1...1 adjustable
Accuracy : ±1% de la valeur mesurée ou 3% si la valeur est plus élevée
Digital pyrometer with extended sensor head, inbuilt LCD & keypad for parameterization. Stainless steal sensor head and zinc electronic box.
Instrumentation equipment
Instrumentation collage de jauge
FP 2534
Operating temperature: -40 ° C to 120 ° C
Connection: Relay terminals and single-core wiring cables
Gauge type: according to product and applications
The service offered by Mesurex allows the study of deformation of various metals with or without recording of measurements
Potentiometric distancemeter
FP 2186
FP 2186
Range: ± 5mm or ± 25mm.
Resolution : Infinite
Accuracy : ± 1/100mm
This sensor, associated with a wire in Invar for its fixation, was developed to monitor the displacement of objects, frequently used to measure the displacement of walls of old buildings, structures during works or displacements of structures caused by the heat.
Wired displacement sensor
FP 2606
FP 2606
Measurement range: 0 to 50 000mm
Linearity: 0,25%
Output signal: 4 / 20mA or 0 / 10V
Tensioned displacement sensor, preferably used when it's necessary to measure positions over medium and long distances and in confined spaces.
Wired position sensor
FP 2646
FP 2646
Measuring Range: 50 / 1250mm
Resolution: Infinite
Repeatability: ± 0.03% EM
This linear position sensor series with analog output is compact and intended for light applications in dry environments. Models available in 11 different measuring ranges with a maximum of 50"(1250mm).
Sheath Thermocouple
CJ type K, J, T, N, S, etc
FP 2126 CJ
20,00 €HT
Thermocouple with extension cable. Length and diameter of the extension cable on demand. Termination output bare wire or connector to choose. This robust and inexpensive foldable thermocouple model is the ideal model for temperature measurements up to 1200 ° C in solid, liquid or gaseous environments. Shielded Teflon extension cable.
ultra miniature pressure sensor
PPB serie
FP 301 EN rec D
Miniature pressure sensor made of stainless steel designed to perform measurements in corrosive environments.
Standard pressure sensor
-PR -1 à 1.5 Bars Basse pression
FP 2549 300€ UHT
Waterproof pressure sensor with relatively small extent. 0 / 10v or 4/20 mA output signal. Mechanical connection on request. All parts of this sensor are made of stainless steel, a piezoresistive cell. The signal from this sensor is amplified, calibrated, compensated and made available as standard voltage or current output.

Standard pressure sensor
-PR 0 à 1000 bar
FP 2548 exemple 250€ UHT
Standard pressure sensor, mechanical connection on demand. Electrical output on DIN connector. Power supply 11/33 vdc. Liquid and gas fluid. Ceramic pressure transmitter. High diversity and variations of pressure connection and electrical connection, staged pressure measuring ranges from 100 mbar. Output signal 0 / 5v, 0 / 10v, 4 / 20mA.

Thermocouple raccord M8X125 CRR
CRR Type K
T FP 2805 CRR M8x125
35,00 €HT
Thermocouple de type K chemisé avec raccord inox M8X125 intégré. La longueur sous filetage est à la demande 10,20,30 mm et autres, chemisé diamètre 2 mm. Terminaison par connecteur miniature. Ce modèle de thermocouple est robuste et peu onéreux, c'est le modèle idéal pour les mesures de température jusqu'à 200/250°C dans les milieux solides, liquides ou gazeux.
Construction monobloc.
Thermocouple Raccord M16x150 CRR
CRR Type K
T FP 2806 CRR M16x150
40,00 €HT
Thermocouple de type K chemisé avec raccord inox M16X150 intégré. La longueur sous filetage est à la demande 5,10,20,30 mm et autres, chemisé diamètre 2 mm. Terminaison par connecteur miniature. Ce modèle de thermocouple est robuste et peu onéreux, c'est le modèle idéal pour les mesures de température jusqu'à 200/250°C dans les milieux solides, liquides ou gazeux.
Construction monobloc.
Low pressure transmitter
-PR 0 à 0.5-0.6bars
FR 2548 REV B
Measuring range: 0 ... 0.5-0.6bars
Mechanical connection:
Output signal: 4 / 20mA, 0 / 5V, 0 / 10V
Application: Industry
Low pressure transmitter, mechanical connection on request. Electrical output on DIN connector. Fluid : liquid and gaz. Ceramic pressure transmitter. Wide variety of variants, connection, pressure and connectivity, step pressure measurement ranges from 50 mbar.
Highly accurate pyrometer
E-series
E450C PL
Measurement temperature : 800°C/2500°C
Spectral range : 0.7...1.15μm
Emissivity : 0.1...1.0 adjustable
Accuracy :±0.5% de la valeur mesurée +1°C
High accurate pyrometer with extended sensor head and separate electronic box. Inbuilt LCD display and keypad for parameterisation. Sensor head : Stainless head. Electronic box : Zinc. 
Vibrometer
FP 2149
A
Measurement range : 0 to 30mm/s
Admitted overload : 20 x EM
Frequency response : 0 to 1KHz
Resonance frequency : 1.5KHz
Signal output : 4/20 mA
Sensor for vibration measurements.
Kapton surface temperature sensor
DS48
FP 2177
17,00 €HT
This low cost thermocouple model, specially designed for surface temperature measurements, has good mechanical strength. It is characterized by great flexibility, the ability to be reusable and its Kapton design (as standard) allows it to be used up to 200 ° C. Other features to consult us.
Thin film sensor temperature
DS2047X2F1M
FP 2700
105,00 €HT
Platinum probe type PT100 flexible and ultra fine, 2 wire connection with 28 gauge, unshielded. Can be used on rounded or flat surfaces (piping, between layers, ...)
Thermocouple Film Kapton DS7 (0.25mm)
DS7
FP 2802
80,00 €HT
Thermocouple developed by MESUREX under Kapton © flexible tape for measuring surface temperatures.
PT100 de surface DC19P4
DC 19P4
T FP 2812 DC19P4
30,00 €HT
PT100 de surface sonde platine, idéal à positionner avec son support silicone adhésif, utilisation en surface, pastille en silicone de diamètre 18  m et d'épaisseur 4 mm
réutilisable, tenue en température -20/65°C, câble d'extension en longueur 2 mètres en standard non blindé montage 2 fils. A partir de la classe A.

Capteur très haute pression PRHP
Capteur très haute 0/4000bar
P FP 2386 PRHP
Etendue de mesure : 0/4000 Bar
Raccord mécanique :  M20x1.5
Signal de sortie :       Bas niveau
Application : industrie, laboratoire, aéronautique, R et D.

Capteur très haute pression, raccord mécanique M20x1.5. Sortie avec un câble avec presse étoupe. Alimentation 5 vdc. Fluide liquide et gaz. Signal de sortie bas niveau
Thermocouple souple FKK
FKK
FP 2416
15,00 €HT
Thermoelementtyp K, J, T
Low temperature IR pyrometer
ML-series
ML-2W/2WH
Measurement temperature : 0°C/1000°C
Spectral range : 8...14μm
Emissivity : 0.1...1.2 adjustable
Accuracy :±2% of the measured value +3°C
Rugged and compact IR pyrometer designed for low temperature applications needs (very small size). Digital TTL output and alarm output.
flexible thermocouple
FTT/ FIT / FGG / FHH
FP 2164
15,00 €HT
Temperature sensor in Teflon cable or glass silk cable. Wire dimensions and length of probe on demand. Very flexible sensor with connector of diameter and length on demand.

Affordable thermocouple
Thermocouple FTTORS
FP 2154
10,00 €HT
This model of temperature sensor is characterized by its flexibility, ease of implementation and low price. Ideal for measurements of surface temperature or in materials (thermocouple lost during cooking, for example). Single thermocouple delivered with hot soldering exposed and realized. Very short response time thanks to the small conductor diameter (0.2 mm or 0.5 mm). Each conductor is Teflon® insulated. Choice of output, bare wire or connector. (Lengths on request).

Prob
Passage étanche PEC M4 à M10
FP 1510 15€ UHT
Watertight passage or partition penetration for sensor mounting. Bulkhead or stainless steel watertight passage with stainless steel, teflon, copper, brass. For jacketed thermocouple or PT 100 probe in stainless steel tube. Standard thread in M4, M6, M8, M10 others on request.
Thermocouple pastille cuivre DC12
DC12
T FP 2804 DC12
15,00 €HT
Thermocouple type K, J, T etc, with copper pad diameter 12 thickness 0.2 or 0.5 mm with glass fiber cable, temperature resistance 350 ° C with the possibility of adding a miniature or standard compensated connector type
Bayonet thermocouple (IBA)
IBA
FP 2808
Bayonet temperature sensor (IBA) especially used in the plastic industry, but also in other areas.
Threaded temperature sensor
CRR PT100 ou TC
FP 2146
60,00 €HT
Screw type temperature sensor PT100 or TC. On-demand fitting, diameter and thread length ditto. Temperature sensor type PT100 or thermocouple. A monoblock fitting is mounted on the probe. The length and thread diameter are made according to your specifications. The standard extension cable is 2m, with or without a connector of your choice.
Platinum probe PT100 stainless steel sheath
Ref. IJ PT100, PT1000
FP 2167 IJ/SD
30,00 €HT
PT100 type stainless steel sheathed temperature sensor, with 3 or 4 wire extension cable and length on request. Precision of the probe 1/3, 1/5, 1/10 DIN. PT100 type probe, or PT1000 of length and diameter on demand. The Teflon extension cable will be of the requested length. This non-collapsible monoblock probe will allow you to make very precise measurements.
Near flush membrane pressure transmitter
-PR 0 à 0.4-60bars
FP 2548 REV B
Measuring range: 0/0.4-60bars
Mechanical connection: 1/2 male gas, 1/2 male gas, 3/4 male gas
Output signal: 4/20 mA, 0/5V, 0/10V
Near flush pressure transmitter. Electrical output on DIN connector. Ceramic pressure transmitter. The flush type connection allows use on viscous fluids. Output signal 0/5V, 0/10V/ 4/20 mA.
Industrial temperature sensor
CIS ou CIM TC ou PT100
FP 2172
35,00 €HT
Industrial type sensor, with miniature or standard head. PT100 or thermocouple sensor. Diameter and length on request. Possibility to incorporate a 4/20 mA transmitter. For installation in fixed station type furnace, oven, pipe. This sensor can be supplied with a transmitter output signal 0 / 10v or 4/20 mA see other. A calibration can be provided to you on demand.
Wiper temperature sensor
LE49 K
FP 2240 LE49 K
50,00 €HT
Wipper temperature sensor for brake disk measurement with shoe shape, 1 mm pyrocoax, flexible stainless steel blade for hardness of application, fixing by screw 5 mm diameter, pyrocoax length 300 mm and extension cable in Teflon shielded. Termination by miniature K-type connector according to IEC 584-3 standard. Enclosures for fixing pyrocoax. Adjusting screw M3 with spring.
Monobloc temperature sensor
CCL Type PT100
FP 2160
40,00 €HT
PT100 or TC monoblock probe. Diameter and length on demand. Cylinder type connector with number of contacts following probe. PT100 type probe or thermocouple of diameter and length according to your need. The monoblock connector will be of your choice. A calibration of this probe can be done according to your measurement points
Wiper temperature sensor
LE491K
FP 2239 LE491K
Wipper temperature sensor for brake disk measurement with bronze pastille, 1mm pyrocoax, flexible stainless steel blade for harness of application, fixing by screw 5 mm diameter, pyrocoax length 300 mm and extension cable in Teflon shielded. Termination by miniature K-type connector according to IEC 584-3 standard. Enclosures for fixing pyrocoax.
PT100 et PT1000 type SD
SD Mini PT1000 ou PT100
FP 2608
35,00 €HT
Sonde platine de type PT 1000 ou PT100 pour inserrer dans des bobinage ou moteur. Surveillance de l'échauffement. Capteur embarqué ayant subit des tests de validation. Qualification aéronautique suivant matrice de conformité.
Black ball temperature
Boule noire
T FP 2809
Measuring range : -40 ... 80 ° C
Accuracy : 0,15°C (0°C)
Dimensions : 50, 70 or 100mm diameter, 6/10mm thickness.
A black ball for measuring the ambient temperature of the air and the radiation from heating, machinery or sunlight. Adaptable to all types of thermometer.
Thermal stamp sensor
FP 2332
FP 2332
Levels of temperature : 4
Response time : < 1s
Accuracy :±1°C (types 49 et 71), ±1% (types 93, 116 et 138)
This low cost sensor allows to determine fastly and simply the temperature threshold reached. This a miniature band self-adhesive at several temperature levels.
Pitot tube
FP2117
2117
Material: Stainless steel 4/4 hard according to AFNOR: Z2.CND.17.12
Diameter: 3, 6, 8mm
Operating temperature: 650 ° C continuous, 8000 ° C peak
High quality stainless steel pitot tube, idea for dynamic fluid pressure measurements in pipelines to determine the flow rate of the fluid.
The pitot tube is frequently used in the areas of ventilation, climate engineering, air conditioning ...
Sensor temperature with screw
IRJ PT100
FP 2145
Accuracy : Version PT100 : +/-0,15°C à 0°C, +/-0,350C 100°C (classe A)
Version thermocouple K : +/-1,5°C de -40°C à 375°C
+/-0,004x|T°| de 375°C à 1000°C
Operating temperature : PT100 : -200 à 250°C en standard
Thermocouple K : -100 à +1000°C
This model of temperature sensor offers an excellent accuracy, it's designed for temperature measurement upto 250°C in solid, liquid or gas medium.
PT100 platinum sensor
SD-d-L-Type
FP 2167
Operating temperature: -200 to +400°C continuously
Accuracy :+/- (0,15°C + 2 x 10-3x T), soit : ≤ +/-0,35°C à 100°C
Thermocouple : norm EN 60584
This model of platinum or thermocouple probe, which offers high accuracy, is the ideal model for temperature measurements in solid, liquid and gaseous environments. The proposed model is constituted of the sensing element, PT100 platinum probe.
SD IJ temperature sensor
SD standard
FP 2167 SD/IJ
15,50 €HT
PT100 , this proposed model consists of the sensing element, platinum PT100 sensor (100 ohm at 0 ° C according to DIN 43760 and IEC 751) or thermocouple hot welding, tube mounting
Miniature pressure sensor
PKHT
FP 2356
Measuring range : 10/350 bar
Operating temperature : -50°C to 250°C
Repeatability : ±0,2% of EM
These sensors are designed for both static and dynamic pressure measurements in a temperature range of up to 220°C. Made of APX4 stainless steel, they are robust and can be used in difficult environments. They are also insensitive to torque and provide great stability.
Surface temperature sensor
LCU 10x10 type
FP 2121
Precision: Thermocouple K: / - 1,5 ° C from -40 ° C to 375 ° C
PT100 : classe 1 : +/-0,15°C à 0°C
+/-0,35°C à 100°C
This type of surface temperature sensor offers excellent thermal contact thanks to its copper platen.
It is characterized by great robustness. Thermocouple or PT100.
Temperature sensor to screw
DAO PT1000 ou PT100
FP 2607
18,00 €HT
Platinum probe type PT 1000 or PT100 to fix on cases or crankcase. Monitoring of the heating (safety) embedded sensor having undergone validation tests. Aeronautical qualification according to conformity matrix.
PT100 temperature sensor
PT100
FP 2576-1
Temperature range: -200/600°C (
Nominal value: 100 Ω to 0°C (single or double, measuring point 8 mm from the body at the end of the connections)
Temperature coefficient : 3850 ppm/K
Connection wires : Alloy palladium/gold
This sensitive element is made from a platinum wire coiled in a ceramic tube sealed at the ends. Small diameter to insert into piping.
PT100 temperature sensor
PT100
FP 2577
Temperature range : -70°C/500°C (except connector 180°C)
Nominal value : 100 Ω à 0°C
Temperature coefficient : a 3850 ppm/K
This sensitive element is developed by spraying a thin layer of platinum on a ceramic substrate. Integrated lemo connector with crimp pin plug (aero).
PT100 platinum sensor
SD-d-L-Type
FP 2644
Operating temperature: -200 to 250 ° C as standard (500 to 800 °C optional)
Accuracy: +/- (0.15°C + 2 x 10-3x T), soit ≤+/-0,35°C à 100°C
This inexpansive, high-precision platinum probe is the ideal model for both low temperatures and temperature measurements up to 200°C in solid, liquid or gaseous media.
Bare element temperature sensor
PT100 miniature couche mince
FP 2373
3,00 €HT
Temperature sensor for applications where the temperature measurement needs to be precise, for temperatures ranging from -70 ° C to + 500 ° C. Resistive circuit, created by photo lithography and then covered with a protective glass film. The tensile strength of the connections is guaranteed by a drop of glass deposited on the welds. Reduced footprint, electrical isolation and reduced response time.
PT100 / 1000 winding insert probe
ZP121X380 TEC
FP 2647 C
30,00 €HT
Sonde platine de type PT 1000 ou PT100 pour inserrer dans des bobinage ou moteur. Surveillance de l'échauffement (sécurité). Capteur embarqué ayant subit des tests de validation. Qualification aéronautique suivant matrice de conformité.
right-angled thermocouple
CJPEC3K5 series
FP 2652-B
45,00 €HT
This model of thermocouple, pliable and sturdy, is ideal for temperature measurement up to 1000°C in solid, liquid or gaseous environment. The 2 thermocouple wires are isolated in magnesia compacted in Inconel 600 sheath.
Temperature sensor with transducteur
IRJM
FP 2327
600,00 €HT
Temperature sensor, with integrated transmitter. Interesting product for assembly in very confined environments. This sensor can be embedded.
Friction temperature sensor
SE49 K
FP 2236 SE49K
75,00 €HT
Friction temperature sensor for measurement on brake disc with bronze shoe, pyrocoax in 0.5 mm, adjusting screw for hardness of application, fixing by screw diameter 5 mm, temperature measurement by pyrocoax of length 500 mm and a miniature connector type K. According to IEC 584-3 standard.

Ambient temperature sensor
ATA
FP 2144
45,00 €HT
This model of temperature sensor is available in platinum PT100 or thermocouple version. It is ideal for room temperature measurements. This range of sensors is equipped with a shielded Teflon extension cable and a mounting plate.





Ambient temperature sensor
P121
FP 2612
6,00 €HT
The ideal temperature sensor for measuring ambient temperatures in small spaces, it is specifically designed for electric motors.
Ceramic temperature sensor
P115HT
FP 2557 10€ UHT
This sensor has been developed for its stability when measuring temperatures above 800 ° C or when there is a risk of thermal shock. Available with one or two probe.
Thermocouple needle
PJ/PM K,J,T etc
FP 2158
25,00 €HT
Prick probe in pasty or rubbery material. Diameter and length on request. The cable will also be mounted according to your needs. A connector can be mounted at the end.
Temperature sensor with clip
DSCLIP1
FP 2645
50,00 €HT
Temperature sensor developed especially for tube measurement of different diameters. Fast fixing, robust and reusable. It exists with different types of probes, PT100, PT1000, and thermocouples K, J, T, S, N etc.


PT100 surface sensor
LCU 10
FP 2159 LCU
25,00 €HT
This platinum probe model (here with 2-wire miniature copper connector), specially designed for surface temperature measurements, has excellent thermal contact. It is characterized by great mechanical flexibility and the ability to be reusable.
Sheathed thermocouple with tinsel
DC
FP 2363 DC
35,00 €HT


Miniature pressure sensor
P-XCC--KP5V Serie
FP 103 EN Rev F
Miniature pressure sensor, allows mounting in very small areas. This sensor makes measurements in static, but also in dynamics. Electronics can be integrated to deliver a voltage signal.
Miniature pressure sensor
PXC/C-Serie
FP 108 Rev B
Miniature pressure sensor, allows mounting in very small areas. This sensor makes measurements in static, but also in dynamics. Electronics can be integrated to deliver a voltage signal.
Miniature pressure sensor
PXC-Serie
FP 103 Rev F
Miniature pressure sensor, allows mounting in very small areas. This sensor makes measurements in static, but also in dynamics. Electronics can be integrated to deliver a voltage signal.
Miniature pressure sensor
PAPC4KP5V
FP 101 Rev C
Miniature pressure sensor, allows mounting in very small areas. This sensor makes measurements in static, but also in dynamics. Electronics can be integrated to deliver a voltage signal.
Miniature pressure sensor
PK serie
FP 505 Rev D
Miniature pressure sensor, allows mounting in very small areas. This sensor makes measurements in static, but also in dynamics. Electronics can be integrated to deliver a voltage signal.
Miniature pressure sensor
PN Serie
FP 401
Miniature pressure sensor, allows mounting in very small areas. This sensor makes measurements in static, but also in dynamics. Electronics can be integrated to deliver a voltage signal.
Miniature pressure sensor
PBC Serie
FP 202 Rec N
Miniature pressure sensor, allows mounting in very small areas. This sensor makes measurements in static, but also in dynamics. Electronics can be integrated to deliver a voltage signal.
Miniature pressure sensor
PB Série
FP 201 rev F
Miniature pressure sensor, allows mounting in very small areas. This sensor makes measurements in static, but also in dynamics. Electronics can be integrated to deliver a voltage signal.
Miniature pressure sensor
PSX1C Serie
FP 107 Rev L
Miniature pressure sensor, allows mounting in very small areas. This sensor makes measurements in static, but also in dynamics. Electronics can be integrated to deliver a voltage signal.
Humidity/temperature sensor
2614-A
FP 2614
Measurement scale (temperature) : -10°C to 100 °C
Output signal : 100 ohms à 0°
Measurement scale (humidité) : 0 to 100%
Output signal : 0.8 à 3.9 Vcc
Sensor for indoor measurement, mounted on a vertical side.
Miniature pressure sensor
PM Serie M6x1
FP 502 rev F
Miniature pressure sensor, allows mounting in very small areas. This sensor makes measurements in static, but also in dynamics. Electronics can be integrated to deliver a voltage signal.
Temperature sensor
SWI4
FP 2811
This rugged temperature sensor model is the ideal model for surface temperature measurements on pipes and ducts. It is designed from a standard hose clamp on which we integrate a measurement element such as thermocouple or PT100. The element is encapsuled in order to be protected.
traction/compres. force sensor
FTCNS 25 à 750 kN
FP 3403 800€ UHT
Standard force sensor, 25 to 750 kN capacity, 5 m cable output, 2 mV / V low level output signal. Very high capacity sensor for use in tension and compression for fatigue testing applications. Its advantages are to ensure a low deformation and sensitivity to transverse forces. IP66 protection and stainless steel body ensure a high degree of robustness.

traction/compres. force sensor
-FTCP 10 kN à 30 MN
FP2346
Traction and compression force sensor. Male/male thread, low level output signal. Output on cable or connector. Its high capacity and good accuracy make it the ideal sensor as a standard. It meets the standards ISO 376 and En10002-3. Its IP66 or IP68 protection gives it a robustness in harsh industrial environments. Made of stainless steel or alloy steel.
Force sensor wafer-type
FC 500N 35-69
FP3503 500€ UHT
Annular compression force sensor wafer-type. Force sensor, slab type, for use in compression. Sensor of small thickness. Equipped with a mechanical stop, accepts an overload without being damaged.
S force sensor
FTCS 50 à 10 000 N
FP 3301
Type S force sensor, work in traction / compression. 2 m cable output as standard. Signal low level 2 mV / V. This type of very robust sensor is suitable for the measurement of high accuracy on test bench as in industry. Its level of protection allows it to be used in aggressive environments. Optional analog output.
Miniature force sensor
FOMT8x3.5
FP3501 300€ UHT
Miniature force sensor in small compression, for static and dynamic applications. Stainless steel or aluminum version. This type of sensor is offered as a load washer version with a diameter of 8 mm, ideally designed to measure forces from 10 to 100 N. It is therefore suitable for any application requiring a low height sensor having a reduced mass.
Miniature force sensor
FTCP 500 à 10 000 N
FP3101 500€ UHT
Miniature force sensor traction/compression,  M5 male / male or male / female. This type of miniature sensor is intended for traction and compressive force measurements both in static and dynamic. Its 2 threads allow easy installation in industrial environment, especially when the size is an important criterion.

traction/compres. force sensor
FTCP 1000 à 50 000 N
FP3100 B 600€ UHT
Miniature force sensor in traction and compression. Small dimensions for large measuring ranges. Equipped with metric threads for use in traction as in compression, these sensors must not be subjected to off-axis loads.
Compression force sensor
-FO 0.3 à 500 kg
FP 2649
Bar type force sensor for use in weighing. Low level 1 mV / V output signal, 2 m extension cable. This load sensor is designed for use in a variety of applications such as commercial weighing or portable systems. It will indicate the correct output value on any surface, or apply the force on the surface of the sensor.

digital weighing sensor
-FO 10T NUM
FP2387 300€ UHT
Weighing sensor with ring and hook, maximum capacity 10 T. Delivered with remote control. Hook and shackle provided. This dynamometer-type sensor is ideally designed for tensile measurements up to 10 T. A remote control allows it to scroll through various remote functions such as changing the stored tare thanks to its small internal memory. Possibility of calibrating this sensor.
Test and deformation service
Instrumentation pièce client
Essai et déformation
Customer part instrumentation with strain gauges. To make tests and measurements with mechanical constraints according to specifications of the customer. Traction/compression, on a table of 500x 500mm with a stress of 50 T max. A video recording can be provided.
humidity/temperature sensor
-TRTH
FP2436 300€ UHT
Small wall mounted sensor for temperature and humidity. Double signal outputs 0 / 10v or 4 / 20mA. This sensor can be mounted inside a room or outside.
Capteur humidité/temp atex
-TRHUATEX2
FP3450
Capteur température et humidité, pour usage en milieu difficile. Matériel homologué pour usage en atmosphères explosives ATEX. Capteur de température et humidité, avec double sorties 4/20mA. Ce capteur est prévu pour être monté sur une paroi ou en plafond. Nous pouvons également vous fournir ce capteur pour des zones dangereuses, ou du matériel ATEX est nécessaire
weather sensor
METEOROLOGIE
-
Temperature and humidity sensor, for outdoor mounting. 4/20 mA output signal. The mounting of this sensor is intended for attachment to a metal mat. Possibility of putting an atmospheric pressure sensor.
Cable extension sensor
-DEP 1000 4/20
FP2606
Cable extension sensor, with stretched wire. 0 / 10v or 4/20 mA output signal. This sensor allows a very fast assembly. Possibility of calibration.

Potentiometric sensor
DPFILINVAR
FP2186
Sensor for displacement measurement with invar wire. 0 / 10v or 4/20 mA output signal. Fast mounting of the sensor, whatever the length. Whatever the temperature of the environment there is no expansion or retraction of the wire. This sensor is used for outdoor environments on structures or monuments.

Anonemeter sensor
-ANEMO 60
FP2609
Anemometer sensor for fixed mounting, 4/20 mA output signal. Sensor for measuring wind speed. Mounted at the end of a mast with a wind vane, it will be a perfect complement to your weather station. Its 4/20 mA signal allows it to be deported at a great distance.

Capteur girouette
-GIROUETTE 4/20
FP2611
Capteur pour la mesure en extérieur de la direction du vent. Signal de sortie 0/10v ou 4/20 mA. Ce capteur est prévu pour être monté sur un mat avec un anémomètre. Bonne fiabilité dans le temps.
Thermocouple Lemo taille 0
Thermocouples à gaine métallique semi-rigide, soudure chaude isolée. Sortie indémontable sur connecteur Lemo série S taille 0, soit prise sur fiche, soit sur prise. Contacts aurés non compensés.
Thermocouple mounted washer
DAO
T FP 2803 DAO
20,00 €HT
Thermocouples suitable for surface temperature measurements of trays, tanks and molds up to 300 ° C (type T) or 400 ° C (type K, J, or N). Hot soldering to the ground.
High temperature magnet thermocouple
These thermocouple on high temperature magnet with support spring allow a good measurement of surface temperature from -10 ° C to + 480 ° C in type K, J or N and from -10 ° C to + 400 ° C in type T. Outlet on 2 or 5 meters of insulated glass fiber cable under stainless steel braid. Sensor allowing contact on a surface at high temperature and over a long period. Provided with an anti-bend spring to protect the cable.
Adhesive thermocouple kapton
Thermocouple for fixing on all surfaces, flat or curved. Temperature range -50 ° C to + 250 ° C. Made from insulated PFA conductors and twisted. The sensitive part is placed under a PTFE impregnated glass fiber high temperature adhesive pellet.
Thermocouple mounted on collar
SWI
45€ UHT
Thermocouple with adjustable collar to measure the surface temperature of piping or pipe diameters from 32 to 300 mm. Three sizes are proposed. The sensing element is in direct contact with the surface. Hot soldering to the ground.
Thermocouple hardened bayonet
Thermocouples built with a flexible cable protected by a stainless steel corrugated pipe, total length 2 meters. Standard bayonet with an ergot. The position of the bayonet is adjusted along the spring, spring length: 200 mm. The hot weld is housed in a cylindrical nozzle of length 18 mm and diameter 4.7 mm. Output on standard male connector with 2 round pins.
Velcro® thermocouple
Velcro® thermocouple is fixed around a pipe, which allows to measure quickly and easily the pipe temperature up to 150 ° C. To ensure efficient measurement, the thermocouple must be in direct contact with the surface.
Thermocouple crocodile clip
Crocodile clip thermocouple to quickly and easily measure the temperature of most surfaces.
Thermocouple on screws
These thermocouple must be screwed directly on the part to measure the temperature of surface or enclosure. Stainless steel screws are available in several sizes. Usable up to 250 ° C.
Miniat. autoclave thermocouple
Thermocouple miniature, conçu pour être employé en autoclave vapeur ainsi que pour les application similaires.
Metallic pyrometric cane
Industrial thermocouple with choice of protective sheaths made of 316 stainless steel, refractory steel, Inconel 600 or Incoloy 800. Classic application: furnaces, drying ovens, boilers, flues, galvanizing baths, heating systems, heat treatment. Several diameters and lengths are proposed. Watertight connection head.
Thermocouple surface / angle 90 °
95€ UHT
Thermocouples equipped with a spiral cord length of 1 meter (extended length) terminated by a miniature male connector with 2 flat pins. Connection possible on any other device, table indicator, regulator, ... Spring blade end, very short response time. Maximum temperature 400 ° C for the measuring end, 105 ° C for the handle and the cable.
Thermocouple air gas
Thermocouples equipped with a spiral cord length of 1 meter (extended length) terminated by a miniature male connector with 2 flat pins. Connection possible on any other device, table indicator, regulator, ... For temperature measurements in a gaseous environment. The protective sheath is perforated, maximum temperature 800 ° C for the sheath, 105 ° C for the handle and the cable.
Thermocouple surface trolley
Thermocouple version with PTFE wheels: low friction, wheels not very aggressive towards the surface; maximum temperature limited to 250 ° C. Version with stainless steel wheels: less respect of the surface. Max temperature 300 ° C.
Economical pt100/pt1000
Pt100 oder Pt1000 steifer Edelstahlmantel.
Very economical Pt100
Pt100 is equipped at the end of a 6mm diameter stainless steel probe set on 2 meters of silicone cable. These thermocouples can be used in most applications up to 200°C.
Pt100 miniature male connector
Pt100 rigid stainless steel sheath. The end is obstructed by welding. The sensitive element positioned at the end of the sheath has a length of 10mm. It is recommended to immerse at least 50mm of sheath in the environment to be measured. Output on miniature size male connector (3 flat pins). The corresponding female connector is available as an option.
Pt100 Hirschmann connector
Pt100 stainless steel rigid sheath with welded end. The sensitive element positioned at the end of the sheath has a length of 3mm. It is recommended to immerse at least 50mm of sheath in the environment to be measured. Termination on DIN 43650, ISO 4400, EN 175301-803 base. Corresponding connector supplied for cable mounting.

Pt100 for stator
These Pt100s are specifically designed to measure and monitor the temperature of motor and generator stators. They consist of a fiberglass blade to be inserted into the slots of the stators. Due to the long sensing range, these sensors can easily detect any heating, even when they are very localized.
Pt100 for autoclave
This simpler model than autoclave load probes uses the same manufacturing technique, but it is not equipped with stainless steel corrugated pipe or bulkhead sealing pipe. Simplex (a Pt100 circuit, 3 wires per circuit) or duplex (two Pt100 circuits, 3 wires per circuit).
Pt100 shrink/output on cable
Shrink is the only viable solution when the application simultaneously requires that the response time is short, the sensors are robust and their price affordable. The end is narrowed: small diameter, low thermal mass, short response time. Non-removable output on 2 meters of PFA insulated cable. The maintenance of the cable on the sensor is entrusted to a metal junction box.
Thermistor
PTC thermistors available in lengths from 2 to 20 meters. If you need to connect these sensors to an instrument not listed in the catalog, check the input characteristics of the device to ensure compatibility with our thermistors. If you are looking for a thermistor with other characteristics ohmic or in another form, consult us.
Thermistor NTC
Thermistor NTC 10 000 ohms, 25 °C with waterproof head IP67. We offer a range of thermistors compatible with our devices. If you need to use these probes with other devices please check compatibility with the device supplier.

Thermocouple surface à lamelle
LM
Thermocouple Pt11. Une bande de chromel et une bande d'alumel sont soudées bout à bout. Épaisseur 3/10mm, largeur 6mm, longueur 200mm.
Canne pyrométrique haute temp
FUB
Thermocouple sous perles céramique 1400°C type K, J, T. Ce modèle de capteur de température est conçu pour les mesures de haute température, dans les milieux solides, liquides ou gazeux.
Thermocouple surface encoche
LE1
Thermocouple Pt101 à encoche destiné à être logé dans une encoche et fixé en place. Il est étanche et isolé électriquement sous 3000 volts. L
Thermocouple ou PT100 surface
DC1
Thermocouple ou Pt100 de surface Pyrocoax pliable avec rondelle pleine pour une meilleur prise de température de surface. Modèle très robuste.
Thermocouple imersion/ambiance
AAM
Thermocouple pour immersion et ambiance. Le capteur est monté dans un tube ajouré pour un meilleur temps de réponse, tout en étant protégé. Version avec manche. Les capteurs de mesure d'ambiance sont conçus pour répondre rapidement à un changement de température souvent faible (ambiance) dans un corps mauvais conducteur de chaleur (air,gaz); d'où l'utilisation d'un élément sensible le plus petit possible. Toutefois en atmosphère polluée ou poussiéreuse ou sujette aux chocs, il peut être inévitable de monter le capteur dans un tube plein qui sera alors d'épaisseur de parois très faible (2/10 généralement). Ceci afin de ne pas nuire à la sensibilité du capteur.
Monter le capteur éloigné des parois afin d'éliminer l'influence de température des parois, important surtout lors des démarrages ou des changements de cycle thermique.
Thermocouple temp ambiante AVA
AVA
Thermocouples de température ambiante. Ce modèle de capteur de température existe en version sonde platine Pt100 et en version thermocouple. Il est idéal pour les mesures de température ambiante grâce à son tube ajouré. Ce capteur est doté d'un corps fileté, facilitant sa fixation, prolongé par un câble d'extension en Téflon blindé.
Thermocouple immersion
AVI
Thermocouples de température d'immersion. Ce modèle de capteur de température existe en version sonde platine Pt100 et en version thermocouple. Il est idéal pour les mesures de température en immersion. Ce capteur est doté d'un corps fileté, facilitant sa fixation, prolongé par un câble d'extension en Téflon blindé.
Detecteur de force FSR
FSR ultra-flat force sensors have an ohmic resistance that decreases when pressure is applied to them.
MESUREX
Zone industrielle Saint Arnoult
13 rue des Corroyes
78730 Saint-Arnoult en Yvelines
T: +(33) 1 30 41 23 62
F: +(33) 1 30 41 23 80
mesurex@mesurex.fr
Notre équipe répond
à vos questions
au 01 30 41 23 62.