Une question ?
Appelez-nous au
01 30 41 23 62
fabricant de capteurs
et systèmes de mesure

STOCK IMPORTANT en thermocouple



traction/compres. force sensor
FTCN 100 à 20 000 N
FP3400 D
650,00 €HT
Force sensor type from 100 to 20 000 N. Output on 2 m cable. Low level signal 1.5 mV / V. This good capacity sensor is intended for use in traction and compression. It is intended for fatigue tests. Its advantages are to ensure a low deformation and an insenability to the transverse forces. IP66 protection and its stainless steel body ensure its robustness.
Miniature force sensor
FC 10 à 5000N9
FP3502
500,00 €HT
Miniature force sensor in compression. Washer type, for use in compression. Sensor of small thickness. Intended for static or dynamic measurements. This sensor is available in 2 forms, with or without central hole, diameter 8 mm.
traction/compres. force sensor
FTCS 10 à 200 N
FP3300 600€ UHT
Miniature force sensor in tension and compression. Force sensor, small dimensions for large measuring ranges. Equipped with metric threads for use in traction as in compression, these sensors must not be subjected to off-axis loads.
traction/compres. force sensor
FTCNS 25 à 750 kN
FP 3403 800€ UHT
Standard force sensor, 25 to 750 kN capacity, 5 m cable output, 2 mV / V low level output signal. Very high capacity sensor for use in tension and compression for fatigue testing applications. Its advantages are to ensure a low deformation and sensitivity to transverse forces. IP66 protection and stainless steel body ensure a high degree of robustness.

traction/compres. force sensor
-FTCP 10 kN à 30 MN
FP2346
Traction and compression force sensor. Male/male thread, low level output signal. Output on cable or connector. Its high capacity and good accuracy make it the ideal sensor as a standard. It meets the standards ISO 376 and En10002-3. Its IP66 or IP68 protection gives it a robustness in harsh industrial environments. Made of stainless steel or alloy steel.
Force sensor wafer-type
FC 500N 35-69
FP3503 500€ UHT
Annular compression force sensor wafer-type. Force sensor, slab type, for use in compression. Sensor of small thickness. Equipped with a mechanical stop, accepts an overload without being damaged.
S force sensor
FTCS 50 à 10 000 N
FP 3301
Type S force sensor, work in traction / compression. 2 m cable output as standard. Signal low level 2 mV / V. This type of very robust sensor is suitable for the measurement of high accuracy on test bench as in industry. Its level of protection allows it to be used in aggressive environments. Optional analog output.
Miniature force sensor
FOMT8x3.5
FP3501 300€ UHT
Miniature force sensor in small compression, for static and dynamic applications. Stainless steel or aluminum version. This type of sensor is offered as a load washer version with a diameter of 8 mm, ideally designed to measure forces from 10 to 100 N. It is therefore suitable for any application requiring a low height sensor having a reduced mass.
Miniature force sensor
FTCP 500 à 10 000 N
FP3101 500€ UHT
Miniature force sensor traction/compression,  M5 male / male or male / female. This type of miniature sensor is intended for traction and compressive force measurements both in static and dynamic. Its 2 threads allow easy installation in industrial environment, especially when the size is an important criterion.

traction/compres. force sensor
FTCP 1000 à 50 000 N
FP3100 B 600€ UHT
Miniature force sensor in traction and compression. Small dimensions for large measuring ranges. Equipped with metric threads for use in traction as in compression, these sensors must not be subjected to off-axis loads.
Compression force sensor
-FO 0.3 à 500 kg
FP 2649
Bar type force sensor for use in weighing. Low level 1 mV / V output signal, 2 m extension cable. This load sensor is designed for use in a variety of applications such as commercial weighing or portable systems. It will indicate the correct output value on any surface, or apply the force on the surface of the sensor.

digital weighing sensor
-FO 10T NUM
FP2387 300€ UHT
Weighing sensor with ring and hook, maximum capacity 10 T. Delivered with remote control. Hook and shackle provided. This dynamometer-type sensor is ideally designed for tensile measurements up to 10 T. A remote control allows it to scroll through various remote functions such as changing the stored tare thanks to its small internal memory. Possibility of calibrating this sensor.
Detecteur de force FSR
FSR ultra-flat force sensors have an ohmic resistance that decreases when pressure is applied to them.
MESUREX
Zone industrielle Saint Arnoult
13 rue des Corroyes
78730 Saint-Arnoult en Yvelines
T: +(33) 1 30 41 23 62
F: +(33) 1 30 41 23 80
mesurex@mesurex.fr
Notre équipe répond
à vos questions
au 01 30 41 23 62.